,

ST-link V2 Programmer for STM8 and STM32

SKU: DSM142

Product Details

  • Product: ST-link V2 Programmer
  • Input voltage: 3.3V to 5V
  • Programming speed: 9.7 Kbytes/s to 12.5 Kbytes/s
  • Self recovery fuse: 500mA
  • Operating temperature: 0℃ to 50℃
  • Dimension: 55mm x 15mm x 5mm
  • Case material: aluminum alloy
  • Package contains
    • 1 x ST-link V2 Programmer
    • 1 x connecting jumper wires

249.00

Additional Info
  • Product image is for reference purpose only.
  • Prices shown are inclusive of GST.
  • Now pay the Lowest shipping of Rs.49 Only
  • Free shipping on value > Rs.999.
  • COD Now Available at extra charge of Rs.50
  • Upto 70% Off on Bulk Orders. Whatsapp Us now.
  • ST-Link V2 programmer allows you to upload. Record, debug programs (along with other functions) in microcontrollers of the STM8 and STM32 family, with high-performance and cost-effective execution makes it perfect for students, hobbyists, and beginners in the area of microcontroller programming. 

    The device supports the full range of STM32 SWD debugging interface, a simple 4-wire interface (including power), fast, and stable. This module is fully consistent with the official version, supports automatic upgrade, supports the full range of STM32 SWD ( only 4 pins including SWCLK, SWDIO, and power) and STM8 (only 4 pins including SWIM, reset, and power) download and debug. 

    The device is quite simple to use and can be used to send code to 32-bit STM32 ARM cortex or 8-bit STM8 microcontrollers. The header of this programmer contains for 5V, 3.3V, SWCLK, SWDIO, SWIM, reset (RST/NRST), and GND. The connector on the opposite side of the device is a USB connector and is intended to be plugged into the computer. 

    Features

    • Use an aluminum alloy U disk shell to install the internal motherboard.
    • The interface definition is directly marked on the enclosure.
    • 5V, 3.3V at the same time to provide external use, convenient for you to connect 5V and 3.3V target boards.
    • The shell characters use laser engraving, never fade off, and permanent clarity.
    • The internal motherboard with 500mA self-recovery fuse, completely protects your expensive computer motherboard.
    • Red and Blue double color LED indicator lamp, it is convenient for you to observe the working state of ST-LINK V2 at all times.
    • Distribution Dupont wire, so that you can easily deal with the wire sequence of different target boards.
    • The outer package is made up of an anti-static bag and a sealed pack by an automatic sealing machine. It is safe and reliable and not afraid of static electricity or water.
    • Support firmware automatic upgrade
    • Support the full range of STM8 SWIM download debugging. Supported software version:
      • XTW LINK ST Utility 2.0 and above
      • STVD 4.2.1 and above
      • STVP 3.2.3 and above
      • IAR EWARM V6.20 and above
      • IAR EWSTM8 V1.30 and above
      • KEIL RVMDK V4.21 and above

    Swim Specific Features

    • 1.65V to 5.5V application voltage supported on the SWIM interface.
    • SWIM low-speed and high-speed modes supported.
    • SWIM programming speed rate: 9.7 Kbytes / s at low speed and 12.8 Kbytes / s at high speed.
    • SWIM cable for connection to the application via an ERNI standard vertical connector or horizontal connector.
    • SWIM cable for connection to the application to the application via a pin header or a 2.54mm pitch connector.

    JTAG/SWD Specific Features

    • 1.65V to 5.5V application voltage supported 
    • JTAG cable for connection to a standard JTAG 20-pin pitch 2.54mm connector
    • JTAG supported
    • SWD and SWV communication supported
    • 1000 Vrsm high isolation voltage 

    Note: Product is available in different color and will be shipped randomly 

    SKU: DSM142 Categories: ,

    Based on 0 reviews

    0.0 overall
    0
    0
    0
    0
    0

    Be the first to review “ST-link V2 Programmer for STM8 and STM32”

    There are no reviews yet.